Skip to content
Shoei J-Cruise II Open-Face Helmet - Matte Blue Metallic
0132-0132-05
- Call for Price - We Offer The Best Prices - Cell: 805-907-8811
- In stock, ready to ship
Earn [points_amount] when you buy this item.
- Earn 5% in Ride Rewards
- Authorized Shoei Dealer
- Free UPS 2 Day Shipping on Shoei Helmets ⚡ (Lower 48)
- No Sales Tax, except California
- 90 Day Free Returns & Exchanges
Why is proper helmet fitment important?
- Helps improve helmet safety
- Maximizes comfort
- Reduces noise levels and distractions
- Helps keep the helmet on the rider’s head during an accident
- Helps maximize the safety benefits of the helmet
- ***Safety standards (like DOT or SNELL) are valid only for properly fitting helmets
Finding the right size to start with:
- Pass a soft, flexible tape measure horizontally around the head, approximately 1-inch above the eyebrows
- Move the tape measure up and down slightly to find the largest measurement
- Cross reference with the appropriate size chart and select the helmet size that is closest to the measurement
- If the head measurement falls between 2 sizes, then try on the smaller of the 2 helmets first (use the size chart as a starting point)
When the helmet is on, complete these steps:
- Check that the helmet inner lining fits snugly all around the rider’s head
- Check that the top pad presses on the top of the rider’s head
- Check that the cheek pads press against the rider’s cheeks. When opening and closing the mouth, the rider’s teeth should drag along the inside of the cheeks.
Confirm these aspects of fitment:
- Make sure you CANNOT easily slide two fingers into the helmet along the side of the rider’s temple
- With the chinstrap properly fastened, grab the helmet with one hand on each side. Without moving the head, try to move the helmet up/down and side-to-side.
- The rider should feel the skin of the head and face being pulled as the helmet is moved, and it should not be easy to move.
- If the helmet can be moved around easily and does not “grab” the rider’s cheeks, it is TOO BIG!
Signs a helmet is TOO BIG:
- Helmet may “fall” onto the head with little resistance
- Noticeably loose around the crown of the head
- Eyes are located near the top of the helmet’s viewpoint
- Helmet can move independently of the rider’s head, no pulling on the skin when helmet is moved up/down and side-to-side
Signs a helmet is TOO SMALL:
- Helmet will be extremely difficult to put on
- Likely to cause immediate pressure points
- Eyes are likely located lower within the helmet’s viewpoint
Signs a helmet fits PROPERLY:
- Helmet may take some effort to slide over head
- Helmet should fit snugly around the crown of the head, without overwhelming pressure
- Eyes are located in the center of the helmet’s viewpoint
Rotation Tests that must be performed:
STEP 1
- Securely fasten the chin strap
- Place your hands on the back of the helmet
- Try to push the helmet off by rotating it forward
STEP 2
- Place your hands on the front of the helmet
- Try pushing it off by rotating it rear-ward
RESULTS: With the correct size helmet, there should be LITTLE MOVEMENT, and the helmet should stay SECURELY IN PLACE.
Not your average open-face helmet, the J-Cruise II is compact, lightweight, aerodynamic, and packed full of innovative technology. Featuring a lengthened internal sun shield for optimal sun-glare protection, all-new “first position” shield opening for advanced ventilation and defogging, enhanced aerodynamics, ventilation and noise-reduction technology, and the ability to seamlessly integrate with the SENA SRL/SRL2 Communication Systems, the J-Cruise II does it all while keeping you safe and connected with the road ahead.
INTERCOM READY DESIGN
- Designed for seamless integration with the SENA SRL/SRL2 Communication Systems
- SRL and SRL2 are specially developed for SHOEI and sold exclusively by SENA
VENTILATION PERFORMANCE
Valuable time spent in SHOEI’s in-house wind tunnel yielded significant improvements in the J-Cruise II’s ventilation performance. Adding an extra intake hole to the upper air ventilation system increased the air volume entering the helmet by approximately 30%. Additionally, a new, patent-pending top air outlet design has improved hot air expulsion by 20%.
AERODYNAMICS & NOISE REDUCTION
Thanks to a more compact, aerodynamic shell shape that features an integrated spoiler, along with strategically-shaped air intake and exhaust vent covers, a new airtight window beading, the shield’s integrated air dam, and an enhanced internal sun shield system, the all-new J-Cruise II boasts significant aerodynamic improvements while preventing unwanted wind noise inside the helmet.
SHIELD SYSTEM
The J-Cruise II’s advanced shield and base plate system provides a large, distortion-free view, facilitates smooth and easy shield changes, features an all-new “first position” shield opening, and comes equipped with a lengthened internal sun shield for optimal relief from sun glare in one quick motion.
SAFETY
Few characteristics of a motorcycle helmet are as critically important as its first and second layers of defense, which is precisely why the J-Cruise II features the SHOEI-exclusive Multi-Ply Matrix AIM shell and Multi-Piece/Multi-Density EPS liner. Additionally, SHOEI’s patented Micro Ratchet Chinstrap system provides a comfortable and secure closure.
COMFORT
The J-Cruise II is equipped with a fully removable, washable, adjustable, and replaceable 3D Max-Dry Interior System capable of dissipating sweat 2x faster than traditional nylon interiors. Multi-layer cheek pads deliver added comfort and helmet stabilization, and premium synthetic leather along the lower edge of the chee
